DISCOVERING ESSENTIAL PLUMBING SKILLS IS CRUCIAL FOR INSTALLING A BATHTUB

Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub

Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub

Blog Article

Book

What're your concepts about A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Mounting a bath tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily available, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the new bathtub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you mount a new bathtub in your bathroom if you have already bought a brand-new tub and do not need to transform the plan of your previous water system pipes.
Your devices as well as product checklist should make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly bothersome as a result of the restricted gain access to that is typically the case.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipes have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
    Prior to going on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Secure the faucet in position with the maker supplied backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Mounting the Bathtub


    Utilizing the two wood boards under its feet, put the tub in the required setting. The wooden boards are helpful in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
    The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the tub up until the level reviews degree.
    To mount faucets, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
    Activate the water supply and examine all joints and also brand-new pipework for leakages and also tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet as well as the normal electrical outlet for leakages.
    Ultimately, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has actually been made use of at least when as this will certainly settle it into its final placement.

    Getting ready for the Installation


    Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent pressure on the tub.
    Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washers.
    Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final position.

    Tiling Around the Bath tub


    In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, bring about problems with wetness and also feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the market. It is a good idea to fit the floor tiles using water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a serious reader on Tools You Need to Install a New Bathtub , I assumed sharing that excerpt was a good idea. Sharing is good. Helping others is fun. We enjoy reading our article about How to Install a Bathtub.


    24-hour service? Dial here.

    Report this page